Toyota 1nz fe engine full service repair manual. Toyota Yaris, Toyota Echo service manual, repair manual, workshop manual, maintenance, electrical wiring diagrams Toyota Echo, body repair manual Toyota Yaris 1999 2019-02-22

Toyota 1nz fe engine full service repair manual Rating: 5,5/10 591 reviews

Toyota Yaris, Toyota Echo 1999

toyota 1nz fe engine full service repair manual

If the diameter is not as specified, replace the crankshaft. Mark 1 , 2 or 3 Front Mark A051826E01 Reference Number Mark Connecting Rod External Diameter Center Bearing Thickness Oil Clearance 1 43. A001071E01 Underhead Length A098332E01 4. Standard lifter bore diameter: 31. If the oil clearance is greater than the maximum, replace all 4 pistons. A035227E01 n Remove the valve lifters. Standard valve stem diameter: 4.

Next

Toyota 1NZ

toyota 1nz fe engine full service repair manual

If not, turn the crankshaft 1 complete revolution 360° and align the marks as above. Standard protrusion B Union A 29 mm 1. It may cause breakage of the flywheel bolt. Push the bar towards the vehicle front to adjust the belt tension. If the oil clearance is greater than the maximum, replace the camshaft. If it is damaged, smooth the surface with 400-grit sandpaper.

Next

Toyota engine 1NZ

toyota 1nz fe engine full service repair manual

If the bush bore diameter of the cylinder head is greater than 9. If the warpage is greater than the maximum, replace the cylinder head. Installed Lifter Clearance mm in. If the wear is greater than the maximum, replace the damper. Maximum angle reference : 2° If the deviation is greater than the maximum, replace the spring. Installed Lifter Clearance mm in.

Next

Toyota 1NZ

toyota 1nz fe engine full service repair manual

If necessary, replace the bearing caps and the cylinder head together. If the warpage is greater than the maximum, replace the manifold. Seal Packing 4 mm 0. Then remove the intake manifold. Front Mark and Number Front Mark Number No.

Next

TOYOTA YARIS (2005

toyota 1nz fe engine full service repair manual

If the taper and distortion are greater than the maximum, replace the crankshaft. A001191E02 d Check the front marks and numbers and install the bearing caps onto the cylinder block. If the clearance is greater than the maximum, replace the bush. A079670E01 Engine Hanger f Engine Hanger Install the 2 engine hangers as shown in the illustration. Engine Front A050671E04 B 13 mm 0. If the cam lobe height is less than the minimum, replace the camshaft.

Next

Toyota Yaris, Toyota Echo service manual, repair manual, workshop manual, maintenance, electrical wiring diagrams Toyota Echo, body repair manual Toyota Yaris 1999

toyota 1nz fe engine full service repair manual

Standard oil clearance Guide Bush A001478E01 Specified Condition Intake 0. Standard cam lobe height: 44. Paint Mark Timing Mark A081897E01 w Align the alignment pin hole on the camshaft timing sprocket with the alignment pin of the camshaft, and install the sprocket into the camshaft. If the bush bore diameter of the cylinder head is greater than 9. Same as above 6 to 8 3 1.

Next

Toyota 1NZ

toyota 1nz fe engine full service repair manual

If the end gap is greater than the maximum, replace the piston ring and oil ring. Then remove the intake manifold. If necessary, replace the bearing caps and the cylinder head together. If not, turn the crankshaft 1 complete revolution 360° and align the marks as above. If the diameter is less than the minimum, replace the chain and crankshaft.

Next

Toyota Engine Repair Manual Free Download

toyota 1nz fe engine full service repair manual

The following essential operations are not written in this manual, however these operations must be done in the practical situation. Maximum oil clearance Guide Bush Specified Condition Intake 0. Standard journal diameter Journal A037114E01 Specified Condition No. Maximum warpage Surface Cylinder Block Side Cylinder block side Specified Condition 0. Standard connecting rod inside diameter: 17.

Next