Rubber grease should be the one whose viscosity is less affected by such low temperature as — 40 °C — 40 °F. If it is in damaged, loose, bent, dented or worn suspension parts and axle housing, they should be replaced. If it is found faulty, correct or replace. Tightening torque Front caliper bleeder plug b : 11 N·m 1. Otherwise, personal injury may result.
Sensor ring Tightening torque 2. Wheels that are statically unbalanced cause bouncing action called tramp. Circlip amount : Apply sealant 99000-31140 to the mating surface of cylinder and cylinder head. If pump does not rotate smoothly or makes an abnormal noise, replace it. These general precautions apply to many of the service procedures described in this manual, and they will not necessarily be repeated with each procedure to which they apply. Wheel speed sensor Right front 6. Tightening torque Pitman arm mounting nut a : 135 N·m 13.
As this will allow fluid to flow out of hose, have a container ready beforehand. Tightening torque Wheel nuts a : 95 N·m 9. Timing chain tensioner adjuster assembly Tightening torque 2. Thus open refriger- ant container valve 4 to purge the charging line. Then take off bleeder plug cap from brake pipe and connect pipe for pipes 3 to wheel cylinder just enough to prevent fluid from leaking. If condenser fin is bent, straighten condenser fin by using flat head screwdriver or pair of pliers.
Fuel pump B : Hose 2. This indicator is to be used with the follow- ing diagnostic procedure. Using a straightedge and thickness gauge, check flatness of gasketed surface at a total of 2 locations. Grommets must be seated in place. To lock crankshaft pulley, use special tool with it as shown in figure. Bearing cap nut 1 Tighten all nuts to 15 N·m 1. Condenser outlet pipe: Apply compressor oil to O-ring.
Disassembly will spoil its original function. This Suzuki Jimny service repair manual will easily help you with any possible repair that you may encounter. Every major topic such as step-by-step instructions, diagrams, and illustration, wiring schematic, specifications to repair and troubleshoot are being covered in our manual completely. Compression Check Check compression pressure on all 4 cylinders as follows: 1 Warm up engine. If it is out of specification, rebore cylinder and use oversize piston. Close valve 6 gradually while watching pressure increase indicated on gauge 4 and take reading of relief pressure maximum hydraulic pressure. The fuel in the fuel tank is pumped up by the fuel pump, filtered by the fuel filter and fed under pressure to each injector through the delivery pipe.
Camshaft housing bolt : Shim No. Apply rubber grease to bush outer surface. Special tool A : 09941-66010 Tightening torque. Oil is drawn up through the oil pump strainer and passed through the pump to the oil filter. Everyone has to learn somewhere, and that place is the service manual! Tighten a little at a time and evenly among bolts and repeat tightening sequence two or three times before they are tightened to specified torque.
Special tool A : 09924-17810 3 Remove the following parts from engine as previously out- lined. Tightening torque Venturi plug a : 5 N·m 0. It will affect its original performance. Special tool A : 09915-77410 B : 09915-77420 1. The tapered end of cam ring 1 should face the side plate 2. Spring and rod assembly 7.
Piston pin clearance in connecting rod small end 0. As the detectable range of the fuel level sensor is set as 0 to 100%, however, with some models whose fuel tank capacity is smaller, the indicated fuel level may be only 70% even when the fuel tank is full. Simply throw it away when your finished! Make sure all clamps are secure. Is there Go to step 2. Abnormal noise from compressor Condition Possible Cause Correction During compressor Inadequate clearance in piston area piston or. Intake manifold mounting bolt short 20.
Shoe hold down pin 2. After the vehicle is jacked up, be sure to support it on stands. See trol system is in good Fig. Our Mechanic Expert team had worked together and compiled this manual to assist you on servicing, repairing, maintenance, troubleshooting, or component replacement work. Hard-tighten bolts and nuts fastening cylinder block and transmission. To avoid using the wrong symptom, always road test the vehicle first.
Transmission range sensor switch 4. Dwonload Service Repair Manual for Suzuki Jimny Sn413 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 This is the same type of service manual your local dealer will use when doing a repair for your Suzuki Jimny Sn413. Be sure to take reading at more than one place along the length of each stem and guide. Below is a list of items that our manuals covered. If shock absorber is found faulty, replace it as an assembly unit, because it can not be disassembled.