When Summary of the content on the page No. Example: An attempt is made to set Data in the Model Name 0x8001. This command obtains the model name. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Connection Communication is enabled by the use of a D-Sub 9 Pin cross reverse cable.
Refer all servicing to qualified service personnel. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Start of Command Results correspond with the data transmission Refer to the Appendix B Table 3 for the data in detail. R Summary of the content on the page No. Community consists of four alphanu- meric characters case sensitive.
Refer all servicing to qualified service personnel. Command Block Format The code from B0 to B7 as described below are transmitted. Introduction This protocol manual describes the basic configuration and basic operations of various commands used for projector. Details of the request and the response are described below. While replacing the lamp can be done by the end user, it is important to realize that the lamp is usually one of the last things that needs to be replaced.
The category of projector is 0x0a. Example: The item to switch the display is specified when the main power is off. Introduction This section describes the specifications, performance and operations of the network service that is going to be installed in the target projector. The projector responds as follows: Returns the response for the error status in the following format. Approximate Return Waiting Times The await-returntime is approx.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer to the Appendix B Table 1 for details. Information Description Category Category of the equipment Equipment name Name of the equipment Serial number Serial number of the equipment Installation information Installation location of the equipment Community Community name of the equipment Power status Power status of the equipment m. Invalid Item Request The Item No. Setup items Description Port Port number Interval Broadcast interval. Function The equipment information shown below is transmitted as the broadcast packet periodically at certain intervals.
Often times, we receive calls from customers who have spent a few hundred dollars replacing their lamps, only to find that the lamp was not the cause of their discoloration, power on issues, or blinking status lights. Projector Has Blinking Light A constantly blinking green or red status light may indicate one of a few system messages. Details are shown on Appendix. Sometimes, broken remotes or broken buttons on the projector will prevent you from switching to the correct input, so test these too. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. This repair will involve pinpointing the cause of the problem, along with a thorough cleaning of hard to reach cooling channels.
Control request Enables the input to be selected and picture control to be adjusted. Projector checks the Summary of the content on the page No. The conditions of occurrence of the respective errors are shown below. Introduction This section describes the specifications, performance and operations of the network service that is going to be installed in the target projector. This command obtains other information. The pin assignment of D-Sub9 Pin and D-Sub25 Pin is as follows. This function is achieved by broadcasting the equipment information periodically to the network.
Invalid Version The version of the Header is other than 2. Item Error This error occurs when the Item No. Consequently, no error code is also sent. Projector Image is Dull or Dim The likely culprit of a dim projector is the bulb. Category Category number 0x0a of the projector is entered here. Pour toute réparation faire appel à une personne compétente uniquement.
The projector responds as follows: When normal : Returns a space. It is fixed to 02h version 2. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. Header The header consists of Version 8 bits and Category 8 bits.
Quality lamps can be quite expensive and we recommend only replacing the lamps when needed. Summary of the content on the page No. Version This indicates the version number of protocol. Function This responds to the control command and requests for acquiring the status and information supplied from clients. Details of the request and the response are described below. Function The equipment information shown below is tran Summary of the content on the page No.