The dialog permits searching the point a random job or in all jobs. Electronic staff readings are automatically corrected by the collimation error stored in the instrument. A final press restores the previous value. Line cutWith all methods of the program line-levelling, there is the possibility of comparing the height of the last point of a line with a known fixed point and to calcu-late the misclosure. Class Displays block type measurement and measuring program line levelling.
Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. Pt2: The point number of the current measured point dH2: The height difference from the current measured intermediate point to the last measured point. Accept and store new settings. The precisioin mode also monitors measuring distances critical to the staff. However, there is no guarantee that interference will not occur in a particular installation.
After the fourth measurement the electronic line-of-sight error is compared with the stored line-of-sight error and displayed. The adjusted points can also be viewed in the data-manager. First enter all required values and then trigger the measurement. The base module and the corresponding options offered supportvi-sualization, calculation, quality testing and recor-ding of measurement data of various Leica instruments. DarknessEvenly illuminate the measuring area of the staff with a flashlight or spotlight in darkness. Desc The description of the found code is displayed.
After Stores code after making a measurement. Find point Find point is a global function to find internally stored measured points or coordinates. The battery symbol shows the level of battery capacity remaining. Manual code entry, as if no codelist was loaded. Manufacturers of non Leica Geosystems accessories The manufacturers of non-Leica Geosystems accessories are responsible for developing, implementing and communicating safety concepts for their products, and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product. After the tools have been successfully installed, the following program modules are available: Data Exchange Manager Data exchange of fixed points, measurements, code lists and data output formats between the instrument internal memory and the computer.
Symbolic names representing variable values on the display are shown. Rem Remarks to the measurements. Any point of the line can be selected as long as it is different from FixPoint 1. Save measurement and continue to foresight. Precautions:Only use chargers recommended by Leica Geosy-stems to charge the batteries. Tighten tripod's central fixing screw.
Sets the selected job to active. Of the three possible set out parameters only one can be used. Depending on the required accuracy, a possible line-of-sight error or the influence of the earth's curvature may have be taken into consideration. Continue to set out display. After date and time have been entered, they are stored in the system. Special characters Find point Find point is a global function to find internally stored measured points or coordinates. The measurements are continued step-by-step until the maximum amount of measurements has been reached.
An hour glass is displayed to indicate that measurement is in pro-gress. For more information please contact Leica Geosystem's technical services. This mode is intended for test measurements or to optimize tar-get distances. Rem Remarks to the next measurement optional. The fixed heights of the control points can be entered.
The person responsible for the instrument must ensure that all users understand these directions and adhere to them. The job and line names can not be changed afterwards. Free Jobs Displays the amount of free jobs available if only measurements were stored. Do not touch the glass with your fingers. In - entry mode a key is used for 3 letters and one digit. When this mode is activated, the top and bottom limits of the staff are automatically converted to a 3m Invar staff.
As long as no new line is started, the current line can always be continued. Angle conversion from degree to gon has to be done by the user. The measurement can be repea-ted as often as desired. Run the Application Double click the. Activating Precision Mode for line levelling with typical accuracy is possible hut not necessary. Always plug the Lemo-plug with the ferrite core into the instrument.
Edit displayed value Edit a few digits of displayed value: Highlight the desired entry field with the navigation keys. Leaves a sub program or an auxillary function; returns to initial display. The following applies: · · Earth curvature correction is taken into consideration according to instrument settings. With other staff lenghts, measurements up to the upper ends are not possible. Both procedures cover two procedures each.