Engine Stop Switch Lead 8. The brake fluid should also be changed if it becomes contaminated with dirt or water. Therefore the cutter must not be used for other purposes than seat repair. If the screen is damaged, replace it. All pages are printable, so run off what you need and take it with you into the garage or workshop. Right Engine Cover Oil Passage from Feed Oil Pump to Oil filter 5. When air enters the brake lines, brake lever or pedal movement will be partially used in compressing the air.
Air pressure in the fork legs increase with normal use, so the fork action stiffens during opera- tion. The shock to fork seal separates the inner tube from the outer tube. While maintaining the mating surfaces of the right and left crankcase halves constantly parallel, mate the crankcase halves evenly. This manual contains service, repair procedures, assembling, disassembling, wiring diagrams and everything you need to know. Ignition Coil Ground Lead 2. Wheelbase 1 485 mm 58.
This entry was posted in and tagged , on by. Special Tool - Hook Wrench R37. Such a shock to the parts can damage them. Overall Width 820 mm 32. Special Tool - Top Plug Wrench, 49 mm: 57001-1653 Top Plug Wrench, 36 mm: 57001-1705 Torque - Base Valve Assembly: 28 N·m 2. If the coolant is brown, iron or steel parts are rusting. Hot Starter Lever Free Play — — — Air Cleaner Element Oil High quality foam air filter oil —.
You may change the file names of these setting data using a personal computer. Special Tool - Valve Guide Reamer, 5. Because of the danger of highly flammable liquids, do not use gasoline or low flash-point solvent to clean the tank. Often, the tightening sequence is followed twice-initial tightening and final tightening with torque wrench. Also, coat the base where the lip of the element fits.
Chain Slack — — — 317. Special Tool - Hook Wrench R37. This can damage or warp the disc. This manual contains service, repair procedures, assembling, disassembling, wiring diagrams and everything you need to know. You can write the surface condition, weather, etc. Special Tool - Hand Tester: 57001-1394 If the switch has an open or short, repair it or replace it with a new one.
A bent fork may cause difficulty in shifting, or allow the transmission to jump out of gear when under power. If turn the adjusting screw of the acceleration pump, follow the procedure below. Change the coolant in accordance with the Periodic Maintenance Chart see Periodic Maintenance chapter. . If it has scratches or is bent, replace cylinder unit with a new one.
If the damping feels too soft or too stiff, adjust it in accor- dance with the following table. Fuel injection amount is increased Beginner and the ignition timing is retarded. If there is any doubt as to the condition of a needle bear- ing, replace it. Torque - Water Hose Clamp Screws: 1. Release air pressure form the fork legs prior to each race through the pressure relief screw located in each front fork cap.
Do not remove the locknut from the piston rod. Flywheel Lead air vent hoses. Gaskets, O-rings, Oil seals, Grease seals, circlips or cotter pins must be replaced with new ones whenever disassembled. To open it you should use Adobe Reader. . Electrical Leads A two-color lead is identified first by the primary color and then the stripe color. Tighten fasteners to the specified torque using a good quality torque wrench.
Do not use fluid from a container that has been left unsealed or that has been open for a long time. If it is deformed or damaged, replace it with a new one. At this time, apply engine oil to the shim or the valve lifter to keep the shim in place during camshaft installation. Refer to the Service Manual. Chain 20-link Length 323 mm 12.
. If the idle speed is out of specified range, adjust it. Throttle Grip Throttle Cable Free Play Adjustment. Also, the throttle valve may not open fully at full throttle. F1: Fuel injection amount Refer to p. If the spring of either fork leg is shorter than the service limit, it must be replaced.