Kawasaki er 6n abs 2006 factory service repair manual. KAWASAKI Motocycle Manuals Resource 2019-03-05

Kawasaki er 6n abs 2006 factory service repair manual Rating: 5,3/10 339 reviews

Kawasaki

kawasaki er 6n abs 2006 factory service repair manual

Replace the starter motor with a new one if there is any damage or wear. Do not use any other battery except for a 12 V sealed battery as a power source. Fix the clamp to the engine mounting bracket. Main Fuse 30 A 9. Battery 12 V 10 Ah 7. If the purge valve dose not operate as described, replace it with a new one.

Next

KAWASAKI ER

kawasaki er 6n abs 2006 factory service repair manual

Be sure to maintain proper alignment and use smooth movements when installing. Immediately wipe any spilled coolant from tires, frame, engine or other painted parts. . Tube Canister ~ Purge Valve 7. Valve Clearance Standard: Exhaust 0. Use proper tools and genuine Kawasaki Mo- torcycle parts. Brake Line Bleeding The brake fluid has a very low compression coefficient so that almost all the movement of the brake lever or pedal is transmitted directly to the caliper for braking action.

Next

Kawasaki

kawasaki er 6n abs 2006 factory service repair manual

If the throttle grip does not return properly, check the throt- tle cable routing, grip free play, and cable damage. R: Replacement Parts S: Follow the specified tightening sequence. Match clearance in vertical column with present shim size in horizontal column. Brake Hose to Front Master Cylinder 3. Fix the front wheel rotation sensor lead connector to the bracket. Main Fuse 30 A 7.

Next

KAWASAKI Motocycle Manuals Resource

kawasaki er 6n abs 2006 factory service repair manual

Do not touch the spark plug, ignition coil or ig- nition coil lead while the engine is running, or you could receive a severe electrical shock. Run the reserve tank overflow hose between the air suction valve cover and the stick coil. Front Wheel Rotation Sensor Signal 4. Run the radiator fan lead inside the frame. If the oil leakage is found on it, replace the shock absorber with a new one. Clamp Hold the main harness. Clutch Lever Free Play Adjustment.

Next

KAWASAKI Motocycle Manuals Resource

kawasaki er 6n abs 2006 factory service repair manual

So, the heater itself can not be removed. Never drop the throttle body assy, especially on a hard surface. Clamps Hold the rear brake hose. Battery 12 V 10 Ah 8. If there is any irregularity, replace the drive chain. . Main Fuse 30 A 7.

Next

Kawasaki

kawasaki er 6n abs 2006 factory service repair manual

Run the leads under the hook on the reinforce. Fix the brake hose rear brake reservoir tank ~ rear master cylinder to the frame with the clamps. Such a shock to the sensor can damage it. Therefore the cutter must not be used for other purposes than seat repair. Torque - Drive Shaft Bearing Holder Screw: 4.

Next

KAWASAKI Motocycle Manuals Resource

kawasaki er 6n abs 2006 factory service repair manual

Main Fuse 30 A 9. Fix the rear brake reservoir tank to the battery case. Run the reserve tank overflow hose under the stick coil lead. Main Fuse 30 A 4. Make sure the area is well-ventilated and free from any source of flame or sparks;. Road Clearance 130 mm 5.

Next

KAWASAKI Motocycle Manuals Resource

kawasaki er 6n abs 2006 factory service repair manual

Do not remove the radiator cap or attempt to change the coolant when the engine is hot; allow it cool completely. Never reuse old brake fluid. Clutch Lever Free Play Inspection. If the measurement is under service limit, replace the pis- ton. Be sure to hold the front brake when removing the engine. Battery 12 V 10 Ah 6. Intake Air Temperature Sensor 3.

Next