All Button: Use the buttons along the lower left side of the controller. Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment. Is bar between the Wires are broken the voltage 8 to 10 outside two ter- or in the wrong. My pool installer has never installed one and told me they think it is a waste of money!! You are now in the lights submenu. Please check with your installer. If there is more than one Spa Side Switch on the system, the buttons on the second switch will be buttons 5-8, and the buttons on the third Spa Side Switch will be buttons 9-12. Call your pool service person to resolve this problem.
Please check with your installer. Cancel specic auxiliary equipment labels. Please check with your installer. Note A Standard Relay can be mounted piggybacked on top of the Dimmer Relay to allow for a total of eight 8 Relays in Power Center. Important Information on Freeze Protection Freeze protection is intended to protect equipment and plumbing for short periods of freezing only. A list of available colors will be displayed.
The pool cleaner requires that water is circulating to the pool in order for it to operate. Turning on the spa also activates the filter pump after a delay for valve rotation and deactivates the pool cleaner if it is on. The installer will contact the factory to obtain instructions regarding the claim and to determine the location of the nearest designated service center. This just started happening randomly. La consommation dalcool ou de drogue augmente considrablement les risques dhyperthermie mortelle dans une cuve de relaxation.
This means that if you are using your spa when freezing conditions exist, freeze protection will not circulate water to non-spa related equipment that you may have freeze protected e. Pour viter que les cheveux ou une partie du corps puissent tre aspirs, ne pas utiliser une cuve de relaxation si les grilles de prise d'aspiration ne sont pas toutes en place. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98. A message will be displayed informing the user that they must walk out to the heat pump and set it to heat or chill mode as well. Pregnant or possibly pregnant women should consult a physician before using a spa or hot tub. Keep track of wire colors. This pump also activates if the spa is turned on, if the pool cleaner is turned on, if a spa spill-over effect is activated, or if maintain heat is active.
Replace the fuse and turn on power. Lutilisation prolonge dune cuve de relaxation peut tre dangereuse pur la sant. Replaced 3814 driver chip on V9 but still having problems with some relays. First at startup everything was fine then All button controller all lights came on and stayed on. The heat pump compressor is covered for five 5 years. I could live with it but any suggestions? Once you fill registration form, aqualink rs8 manual ebooks are available via our partner sites, details can be found.
When the spa heater is enabled the pump will run at this speed. It is only listed as an accessory. Pour viter que les cheveux ou une partie du corps puissent tre aspirs, ne pas utiliser une cuve de relaxation si les grilles de prise d'aspiration ne sont pas toutes en place. The spillover is disabled while the spa is on. All Button Controller Front View Jumpers for Display Module Multiple Controllers Controller 1 Controller 3 Controller 4 Controller 2 Jumper Settings for Micro Controller Multiple Controllers Figure 2. Canadian installations must be at least three 3 meters from the water. If a different color is chosen, the light will reset to Alpine White, rotate to the selected color, and then automatically lock on to that color.
Return to pool mode to activate the waterfall. The lter pump will continue to run for ve minutes to protect the heater from damage, whenever the heater has red and has been off for less than ve 5 minutes. This makes me uneasy for several reasons. If you have more than one program i. For example, you can program the spa heater to heat to 101 degrees, spa light on, jets on, water features on, and then name the result Romantic Scene. Call your pool service person to resolve this problem.
Avant dutiliser une cuve de relaxation mesurer la tmperature de leau laide dun thermomtre prcis. Ensure that your other thermometer is reading reliably before recalibrating. Heater must be enabled at all times for this feature to maintain temperature. . In previous firmware versions, the system would default to last mode of operation.
This label is tied to the pool filtration mode. The pump must be on if you want to display the pool temperature, or if you want to heat the pool. This delay allows water to cool the heater down by circulating water through it, preventing equipment damage. On top of all this, my 220V pump wouldn't turn on after after resetting the breake a couple of times. To reduce the risk of electrical shock, connect this terminal bar to the grounding terminal of your electric service or supply panel with a continuous copper conductor having green insulation and one that is equivalent in size to the circuit conductors supplying this equipment, but no smaller than no.