The contents are listed on the first page of each section to help you find the item and page you need. Good luck and have a wonderful day. The last segment would start flashing when you ran low on gas. Refer to Service Manual, Page 5-3 3. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. It's not the fastest bike on the road.
But, it still has plenty of power for 2-up riding around town, and single riding on the highway. There is invariably some alternative means of slackening or removing some vital component when service tools are not available and isk of damage has to be avoided at all costs. Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. . Turned out to be a big sacrafice. Route red wire to the front of engine and down to the horn.
It's fine for inter-state travel on the highways. Reattach factory grey wire to horn. Install the new wheel to the rear fork. It is up to you how you decide to cut your motorcycles bodywork to accept the frame slider there are many different ways customers go through this process. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. For 2007 and later Models: Install lower screw 10 through the saddlebag guard, footpeg support and the frame.
If this is not available, use an equivalent which is compatible with an aluminum radiator. Precisely measure location of cut and if in doubt at any point please call us before the install process has begun. Figure numbers usually line illustrations appear in numerical order, within a given Chapter. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate. Use masking tape to completely mask off the area on the body where you will be working. Install saddlebag if removed following the instructions in the appropriate Service Manual or Instruction Sheet.
Download 2005 Suzuki Boulevard C50 Owners Manual Download online right now by following link below. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Remove existing front wheel assembly. Some photos in this section are used for illustration examples only. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. Above the reliability, and at under 600 lbs.
Tighten exhaust header bolts following the instructions in the appropriate Service Manual. Remove the front seat and disconnect the battery. Refer to Service Manual, Page 5-3 3. We do it ourselves to help you do-it-yourself, and whatever your mechanical ability, the practical step-by-step explanations, linked to over 900 photos, will help you get the job done right. Repeat for the other side. I've been on a number of 2,3, and 4 hundred mile treks, never a problem. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner.
To view more specifications, visit our. The center of gravity is near perfect. If equipped with saddlebags, removal may ease installation. It is easy to control for low-s. Footrest support bracket assembly Figure 2.
If you are out for a cruiser you owe it to yourself to stop and check out the C50s. Good luck and have a nice day. Snug these up but do not tighten fully. Cover the throttle bodies to prevent anything from dropping into the engine. Do not re-use brake disc screws. The smaller of the two holes in each arm is the one you place the screws through.
It sounds really great, but with a down side. Route black wire to battery negative connection as shown. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. Discard all other valve stems. As such, there is a good selection of 3rd party add-ons. Now remove the breather hose at bottom of the air cleaner. A passenger should hold onto the motorcycle or the rider with both hands, and keep both feet on the passenger footrests.
Install valve stem assembly L on wheel. If you get a chance to ride one do so. The C50 is the newer brother to the Volusia. Date shared: Nov 18, 2014 File name: suzuki-boulevard-c50-owners-manual-pdf. Lift up the fuel tank. Follow the instructions in the appropriate Service Manual or Instruction Sheet. Re-assemble all saved components to the new chrome rear wheel assembly.